The purpose of this lab is to gain familiarity with using Multisim to construct and simulate the noninverting op amp, inverting op amp, adder, and differential amplifier circuits presented in the module. The effect of external biasing resistors will be demonstrated and calculations of output voltage performed in the homework will be confirmed. This lab will set the stage for the concept of confirming calculations with simulation software for the remainder of the course.
Watch videoWeek 1 ? Op-Amp Introduction.
Design the Op-Amp configurations from the W1 Assignment ?Op-Amp Introduction? in Multisim.
For Non-Inverting Op-Amp:
Analyze the non-inverting Op-Amp circuit to calculate the voltage gain Vout/Vin.
Design a non-inverting Op-Amp with 5% resistor tolerances for RF and RG in Multisim.
Run the simulation to measure the voltage gain Vout/Vin of the amplifier.
Complete the table below:
Non-Inverting Amplifier
Vin / Freq RF RG Calculated Voltage gain = Vout/Vin Measured Voltage gain = Vout/Vin
4 Vrms / 1KHz 1K? 1K?
4 Vrms / 1KHz 1K? 5K?
4 Vrms / 1KHz 5K? 1K?
4 Vrms / 1KHz 5K? 5K?
4 Vrms / 1KHz 5K? 10K?
Answer the following questions:
Does the measured values match the calculated values? If not, explain why they are different?
From your measurements, explain how increase in RG affects the voltage gain? Also, explain how increase in RF affects the voltage gain?
What is the effect of resistor tolerance the voltage gain?
For Inverting Op-Amp:
Analyze the Inverting Op-Amp circuit to calculate the voltage gain Vout/Vin.
Design an inverting Op-Amp with 5% resistor tolerances for RF and RG in Multisim.
Run the simulation to measure the voltage gain Vout/Vin of the amplifier.
Complete the table below:
Inverting Amplifier
Vin / Freq RF RG Calculated Voltage gain = Vout/Vin Measured Voltage gain = Vout/Vin
4 Vrms / 1KHz 1K? 1K?
4 Vrms / 1KHz 1K? 5K?
4 Vrms / 1KHz 5K? 1K?
4 Vrms / 1KHz 5K? 5K?
4 Vrms / 1KHz 5K? 10K?

Answer the following questions:
Does the measured values match the calculated values? If not, explain why they are different?
From your measurements, explain how increase in RG affects the voltage gain? Also, explain how increase in RF affects the voltage gain?
What is the effect of resistor tolerance the voltage gain?
For Op-Amp Adder:
Analyze the Op-Amp Adder circuit with R1 = 2 K?, R2 = 2 K?, R3 = 2K? and Rf = 5 K? to calculate the output voltage Vout.
Design an Op-Amp Adder with 5% resistor tolerances for R1, R2, R3 and Rf in Multisim.
Run the simulation to measure the output voltage Vout. (Voltage at the output terminal of the amplifier)
Complete the table below:
Op-Amp Adder
V1 V2 V3 Calculated Voltage, Vout Measured Voltage, Vout
5 4 2
4 3 1
3 3 3
2 2 2
For each of the above Op-Amps, answer the following questions:
Does the measured values match the calculated values? If not, explain why they are different?
Write the expression for Vout of an Op-Amp Adder.
From your measurements, explain how input voltages V1, V2 and V3 affect the output voltage?
What is the effect of resistor tolerance the output voltage?
For Differential Op-Amp:
Analyze the Differential Op-Amp circuit with R1 = 2 K?, R2 = 2 K?, R3 = 2K? and R4 = 5 K? to calculate the output voltage Vout.
Design a Differential Op-Amp circuit with 5% resistor tolerances for R1, R2, R3 and R4 in Multisim.
Run the simulation to measure the output voltage of the amplifier.
Complete the table below:
Differential Op-Amp Adder
V1 V2 Calculated Voltage, Vout Measured Voltage, Vout
5 4
4 3
3 3
2 2
Create a new word document called ?Lab1_StudentID.docx? with your GID substituted into the file name.
Verify all calculations from analysis and measurements from simulations from steps 3, 4, 5 and 6. Save the results along with the tables and paste the screen captures in the word document. Make sure to answer the questions in each step.

The purpose of this lab is to gain familiarity with using Multisim to construct and simulate the noninverting op amp, inverting op amp, adder, and differential amplifier circuits presented in the module. The effect of external biasing resistors will be demonstrated and calculations of output voltage performed in the homework will be confirmed. This lab will set the stage for the concept of confirming calculations with simulation software for the remainder of the course.
Watch videoWeek 1 ? Op-Amp Introduction.
Design the Op-Amp configurations from the W1 Assignment ?Op-Amp Introduction? in Multisim.
For Non-Inverting Op-Amp:
Analyze the non-inverting Op-Amp circuit to calculate the voltage gain Vout/Vin.
Design a non-inverting Op-Amp with 5% resistor tolerances for RF and RG in Multisim.
Run the simulation to measure the voltage gain Vout/Vin of the amplifier.
Complete the table below:
Non-Inverting Amplifier
Vin / Freq RF RG Calculated Voltage gain = Vout/Vin Measured Voltage gain = Vout/Vin
4 Vrms / 1KHz 1K? 1K?
4 Vrms / 1KHz 1K? 5K?
4 Vrms / 1KHz 5K? 1K?
4 Vrms / 1KHz 5K? 5K?
4 Vrms / 1KHz 5K? 10K?
Answer the following questions:
Does the measured values match the calculated values? If not, explain why they are different?
From your measurements, explain how increase in RG affects the voltage gain? Also, explain how increase in RF affects the voltage gain?
What is the effect of resistor tolerance the voltage gain?
For Inverting Op-Amp:
Analyze the Inverting Op-Amp circuit to calculate the voltage gain Vout/Vin.
Design an inverting Op-Amp with 5% resistor tolerances for RF and RG in Multisim.
Run the simulation to measure the voltage gain Vout/Vin of the amplifier.
Complete the table below:
Inverting Amplifier
Vin / Freq RF RG Calculated Voltage gain = Vout/Vin Measured Voltage gain = Vout/Vin
4 Vrms / 1KHz 1K? 1K?
4 Vrms / 1KHz 1K? 5K?
4 Vrms / 1KHz 5K? 1K?
4 Vrms / 1KHz 5K? 5K?
4 Vrms / 1KHz 5K? 10K?

Answer the following questions:
Does the measured values match the calculated values? If not, explain why they are different?
From your measurements, explain how increase in RG affects the voltage gain? Also, explain how increase in RF affects the voltage gain?
What is the effect of resistor tolerance the voltage gain?
For Op-Amp Adder:
Analyze the Op-Amp Adder circuit with R1 = 2 K?, R2 = 2 K?, R3 = 2K? and Rf = 5 K? to calculate the output voltage Vout.
Design an Op-Amp Adder with 5% resistor tolerances for R1, R2, R3 and Rf in Multisim.
Run the simulation to measure the output voltage Vout. (Voltage at the output terminal of the amplifier)
Complete the table below:
Op-Amp Adder
V1 V2 V3 Calculated Voltage, Vout Measured Voltage, Vout
5 4 2
4 3 1
3 3 3
2 2 2
For each of the above Op-Amps, answer the following questions:
Does the measured values match the calculated values? If not, explain why they are different?
Write the expression for Vout of an Op-Amp Adder.
From your measurements, explain how input voltages V1, V2 and V3 affect the output voltage?
What is the effect of resistor tolerance the output voltage?
For Differential Op-Amp:
Analyze the Differential Op-Amp circuit with R1 = 2 K?, R2 = 2 K?, R3 = 2K? and R4 = 5 K? to calculate the output voltage Vout.
Design a Differential Op-Amp circuit with 5% resistor tolerances for R1, R2, R3 and R4 in Multisim.
Run the simulation to measure the output voltage of the amplifier.
Complete the table below:
Differential Op-Amp Adder
V1 V2 Calculated Voltage, Vout Measured Voltage, Vout
5 4
4 3
3 3
2 2
Create a new word document called ?Lab1_StudentID.docx? with your GID substituted into the file name.
Verify all calculations from analysis and measurements from simulations from steps 3, 4, 5 and 6. Save the results along with the tables and paste the screen captures in the word document. Make sure to answer the questions in each step.

fine arts appreciation

Writing Assignment
Please read and follow all directions for this assignment.
The Writing Assignment is worth a total of 20 points.
Due on or before Friday, July 7, 2017 at 11:59 p.m. (CST)
No late assignments will be accepted.
ALL WRITTEN WORK must be IN YOUR OWN WORDS! Please review CTC’s plagiarism policy or ask me if you have questions about this!
TO SUBMIT YOUR ASSIGNMENT:

Scroll to the bottom of the Papers and Projects page.
Select Writing Assignment.
Follow the instructions for submitting your writing assignment.
No assignments will be accepted by email.
SUBMISSION INSTRUCTIONS:

Complete your assignment using a word-processing software such as Microsoft Word and Open Office (download free software at http://www.openoffice.org).
Save your document as .rtf to ensure that it can be opened at any computer.
You may also attach a .docx file or paste directly into the link.
Submit your assignment through the proper link located BELOW.

WRITING ASSIGNMENT INSTRUCTIONS:

This assignment has two parts. Please submit BOTH parts at the same time.

PART 1: QUESTION & ANSWER (10 points)

Choose one visual artist that was BORN after January 1, 1900 from your book and answer the six questions below.

CRITERIA:

INELIGIBLE artists include: Filmmakers (including animators), actors, and graphic designers. Artists’ works should be in a visual media such as painting, sculpture,
mixed media, installation, drawing, etc.
Ineligible websites: Wikipedia.org, artsy.net, artcyclopedia.com (or any other “general” art site) or any site that is a “sale site.” If you’re not sure about a
website, ASK!
Artists that work as a team count as a single artist.
For each artist: Number, copy, and answer each of the six questions and then answer each question individually (re-write the question and then answer the question).
Points will be deducted for missing or incomplete responses.
Follow the Question and Answer format.
If you have any questions about your selected artist, please email me.
NO CREDIT WILL BE GIVEN FOR INELIGIBLE ARTISTS OR ARTISTS BORN PRIOR TO 1900.
QUESTIONS:

Artist’s name, year of birth, country of birth and the page on which the artist is found in your textbook. (1 point)
Complete website where you found information about the artist. This website must be an “informational” site that is specific to your artist. (1 point)
What is his/her primary media? (1 point)
List TWO locations where the artist’s work is currently displayed or was recently displayed. Be specific. (2 points)
Write a short paragraph about why this artist interests you. For full credit, your response must be at least 80 words. (2 points)
Locate on the Internet one piece of the artist’s work that is not found in A World of Art. Then – IN YOUR OWN WORDS – describe its medium, form, and content (meaning).
Include the full website where you found the work. For full credit, your response must be at least 80 words. (3 points)
EXAMPLE:

Artist’s name, year of birth, country of birth, textbook page where the artist is mentioned:
John Doe, Born 1902, Russia, Page 101

Complete website where you found information about the artist:
www.museumofcontemporaryart.org/johndoe

What is his/her primary media?
Oil paint on wood panel.

List TWO locations where the artist work is currently displayed or was recently displayed:

Museum of Modern Art, NYC and Leo Castelli Gallery, NYC.

PART 2: SHORT ESSAYS (10 points; 5 points per topic)

Points will be deducted for incorrect grammar and spelling.

CRITERIA:

Select TWO questions/topics from the list below.
Write your response in essay format.
For full credit, your response to EACH question/topic must be at least 250 words.
Please re-write the question/topic to which you are responding.
Remember, ALL WRITTEN WORK must be IN YOUR OWN WORDS, and use proper citation format if you choose to use outside sources (other than your textbook).
QUESTIONS:

Sayre names seven major themes in art. Define four and cite examples of each from your book which are not found in Chapter 21.
Discuss the four “roles of the artist.” Cite an example of each from your book not found in Chapter 1.
Explain how the group of artists known as the Impressionists got their name and the major factors that tied them together as a group.
Compare and contrast Venus of Urbino by Titian (1538) and Olympia by Manet (1863).
Describe the origins of the mosque and analyze its chief features.
Explain the rise of Dada and the emergence of Surrealism.