\nThe following gas detector tubes are available for direct reading of concentrations of the toxic gas hydrogen sulfide
\nTube\tConcentration
\n4HT\t1-40%
\n4HH\t0.1-4.0%
\n4H\t10-3200 ppm
\n4M\t12.5-500 ppm
\n4L\t1-240 ppm
\n4LL\t0.25-60 ppm<\/p>\n
Which of these tubes would be satisfactory for detecting OSHA specified ceiling concentration for hydrogen sulfide? Of the satisfactory tubes, which one tests the narrowest range of concentrations?<\/p>\n
– Ceiling (MAC) concentration for hydrogen sulfide (H2S) is 20 ppm.<\/p>\n
2.\tA process engineer proposes a new solvent that will reduce the quantities required by the process and significantly reduce the quantities of solvent vapors released into the air inside the pant. The new solvent is perchloroethylene, and it is expected to reduce the solvent vapors absorbed into the plant by 20% by volume as compared to old solvent? (Stoddard solvent. You are called in as a Certified Safety Professional to evaluate the proposed change to the process. Do you support the process change? Explain your position
\nFor these two questions, you can refer to the Appendix A of the book. <\/p>\n
3.\tA glue making process releases ethylene glycol that becomes generally diluted and intersped through the plant atmosphere. The rate of release is 2.4 cubic feet per hour vapor volume at standard temperature and pressure. The plant dilution system is of general dilution type with makeup air being suppled through windows and doors throughout the plant area? The plant area is 12,000 square feet and the average ceiling height is 16 feet. The problem is to specify the capacity of the general ventilation system required to maintain a steady-state condition throughout this process area that protects against both health and safety hazards due to ethylene glycol. For your information in performing calculations, the following data is provided.<\/p>\n
Ethylene glycol
\n?\tMolecular weight : 62.1
\n?\tBoiling point 197.5 ?C
\n?\tLEL: 3.2%
\n?\tFirepoint -13 ?C
\n?\tFlashpoint: 232 ?F
\n?\tAutoignition temperature: 752 ?F
\n?\tVapor pressure: 0.05 mm at 20 ?C
\n?\tPEL: 50 ppm (ceiling)<\/p>\n
a.\tHow much exhaust ventilation (in cubic feet per hour, general diulution tpe) is required to maintain safety hazards below explosive levels?
\nb.\tHow much exhaust ventilation (in cubic feet per hour, general dilution type) is required to maintain health hazards below OSHA-specified action levels?
\nc.\tHow many plant area room changes would be the level of ventilation calculated in part (b) present?<\/p>\n
4.\tA worker exposure to noise in a given plant is measured, resulting in the following readings for various time periods during 8-hour shift?
\n8:00 A.M.-9.00 AM 86 dBA
\n9:00 A.M.-11 A.M. 84 dBA
\n11 a.m.-12 noon 81 dBA
\n12 noon-1:00 P.M. 101 dBA
\n1:00 P.M-4:00 P.M. 75 Dba<\/p>\n
a.\tPerform computations to determine whether maximum PELs have been exceeded based on TWA calculations.
\nb.\tHave the ALs have been exceeded?
\nc.\tGiven the noise exposure just described, would the employer be required to furnish hearing protectors?
\nd. Would employees be required to use the hearing protectors?
\ne.\tSuppose the engineering control could be devised that could cut the noise level (sound pressure level) in half either in the morning or in the afternoon, but not both. Which would you select? Why? <\/p>\n
5.\tA full revolution press with two engagement points on the flywheel has two hand palm buttons installed at a distance of 16 inches from the point of operation. Calculate the minimum flywheel speed that will permit this press in compliance with standards. Explain why a slower flywheel would be more dangerous.<\/p>\n
\nA hospital administrator wants an estimate of X-ray idle time that has a 95.5 percent confidence of being within 4 percent of the actual percentage. What sample size should be used?<\/p>\n
6.\tA hospital administrator wants an estimate of X-ray idle time that has a 95.5 percent confidence of being within 4 percent of the actual percentage. Previous analysis indicates that on the average X-ray machine is busy 25% of the time. What sample size should be used?
\n7.\tPlease provide answers on the following questions written outside of electric panel.<\/p>\n
a.\tWhat is Level 0 Protective clothing and PPE?
\nb.\tWhat is shock hazard? It determines the voltage to which personnel will be exposed, boundary requirements, and the PPE necessary in order to minimize the possibility of electric shock to personnel.
\nc.\tWhat is arc flash hazard? –
\nd.\tWhat is arc flash boundary?
\n– is the distance at which an electrical arc can flash outward, which may endanger employees working on electrical equipment.
\n– marks the distance from the equipment at which the Incident Energy of an arc flash would be 1.2 cal\/cm?
\n– PPE Program was developed to minimize the risk to AMS employees from safety and health hazards in the work place related to the discharge of electrical energy when working within the arc flash boundary distance.
\ne.\tWhat is 208 VAC? The 208 VAC is most commonly used in the US for commercial applications. It indicates that line to line (L-L) voltage is 208Vac in a WYE configuration.
\nf.\tWhat is NFPA-70E? It is originally developed from the OSHA’s request which helps companies and employees avoid workplace injuries and fatalities due to shock, electrocution, arc flash, arc blast, and assists in complying. It is requirements for safe work practices to protect personnel by reducing exposure to major electrical hazards.
\ng.\tWhat is HRC level? It is the Hazard Risk Category Levels, which is determined by the minimum amount of calories per square centimeter.
\nh.\tWhat type of general safety precautions you need to take while working around electric panels? <\/p>\n","protected":false},"excerpt":{"rendered":"
The following gas detector tubes are available for direct reading of concentrations of the toxic gas hydrogen sulfide Tube Concentration 4HT 1-40% 4HH 0.1-4.0% 4H 10-3200 ppm 4M 12.5-500 ppm 4L 1-240 ppm 4LL 0.25-60 ppm Which of these tubes Read More …<\/a><\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[],"tags":[],"class_list":["post-236221","post","type-post","status-publish","format-standard","hentry"],"_links":{"self":[{"href":"https:\/\/www.benedictsol.com\/blogs\/wp-json\/wp\/v2\/posts\/236221","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.benedictsol.com\/blogs\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.benedictsol.com\/blogs\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.benedictsol.com\/blogs\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.benedictsol.com\/blogs\/wp-json\/wp\/v2\/comments?post=236221"}],"version-history":[{"count":0,"href":"https:\/\/www.benedictsol.com\/blogs\/wp-json\/wp\/v2\/posts\/236221\/revisions"}],"wp:attachment":[{"href":"https:\/\/www.benedictsol.com\/blogs\/wp-json\/wp\/v2\/media?parent=236221"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.benedictsol.com\/blogs\/wp-json\/wp\/v2\/categories?post=236221"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.benedictsol.com\/blogs\/wp-json\/wp\/v2\/tags?post=236221"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}